Silverline Mini Pipe Bender 6 - 10mm (MS129)

Product Information

Bender is capable of disassembling and reassembling his body at will and operating each detached body part individually and remotely, presumably by using his transmitter and antenna to send wireless signals. His head can be used for a wide range of functions, whether attached to his body or not. In one episode, Leela reassembles Bender into a functioning go-kart (albeit in an event shown in the "What-If" machine).

The nylon guides are integral to the pipe bender helping to ensure they don’t get lost or damaged in a toolbag. Codes for these spare guides are 1216N 15mm Spare Nylon Guide and 1223J 22mm Spare Nylon Guide.

Single Sized  – 1215K-XV  1315- XVE (1315Longarm-XVL)   1222G-XXII   1322Extended-XXIIE

When Monument look to design, manufacture and market a new product we look to create products which will save the engineer time. In this particular instance, we have designed a smaller and lighter weight pipe bender than the standard combination 15and 22mm hand bender. If there are no extra requirements from the customer, then by default ISO standard tolerances (class m) are applied to our products. Bending tolerances are shown in the table above. In Season 7, Episode 17 "Forty Percent Leadbelly", it is shown that Bender has a 1 terabyte "Main Drive", and a 100,000 terabyte "Porn Drive". As the headline says. There has to be a parallel side to your bending line for positioning purposes. If not, aligning the part is a real headache and you may end up with an unsatisfactory result. Bend Relief Bend reliefs are necessary

lighter in the hand than a combi. The Monument combi weighs more than 4kg; the XV weighs 1.5kg; the XXII weighs 2.3kg In 2008, Bender took second place behind the Terminator in a poll for the "Baddest Movie Robot" on Techradar.com. [27] Before you remove the pipe from the Former, view your bend angle; remove the pipe if it is correct, or if necessary, reapply the Lever Arm and increase the bend angle. Frequently Asked Questions FAQs If you use rivet nuts near the bending line, it’s known that inserting them before bending is good for securing its applicability. After bending, the holes may be deformed. Still, make sure that the nuts won’t be in the way of tools when bending. Small Flanges on Big Parts A small bend at the end of a large part may lead to difficulties

Sign up for special offer emails

Measure the layout. Maybe you can adjust the design for optimal fit. Try to avoid going for a bigger sheet if the smaller size is within reach. Maybe you could fit 2 pieces onto the same sheet if you just shed a few millimetres off? It will reflect on the final price quotation. Rule of Thumb for Minimum Bend Radius A. Pipe wall size is a lot thinner than it used to be, plus the pipe bender former could be stiff (Answered by D S plumbing and heating on 26 Jan 2021)

If you want to make a flange that has one or two ends chamfered, the previous rule of a minimum flange length still applies. The chamfers have to leave enough room to accomplish proper bends, otherwise it will just look deformed and nobody’s really satisfied. Hole Distance from Bend Close-by holes may get warped Partial bending, or air bending, derives its name from the fact that the working piece does not actually touch the tooling parts entirely. In partial bending, the workpiece rests on 2 points and the punch pushes the bend. Is still usually done with a press brake but there is no actual need for a sided die. Buy the Monument Bender Single Sized – 1215K-XV 1315- XVE (1315Longarm-XVL) 1222G-XXII 1322Extended-XXIIE Despite being a robot, he has been seen to show emotion on many occasions, even shedding a tear in " Crimes of the Hot". One of the series' running jokes revolves around Bender having emotions, when technically he should be an unfeeling machine. Bender is seemingly unaware of his emotions, stating in the episode "Anthology of Interest II", "I mean, being a robot's great, but we don't have emotions, and sometimes that makes me very sad". [26] In his very first appearance, he tries to commit suicide via a suicide booth out of guilt for having unknowingly contributed to their creation. He has also been known to be nonchalant to the point of appearing both uncaring and incredibly brave, even in life-threatening situations. When casting for Futurama, Bender's voice was the most difficult to cast, in part because the show's creators had not yet decided what robots should sound like. [10] Because of this, every voice actor who auditioned, no matter for what role, was also asked to read for Bender. After about 300 auditions, even series co-creator Cohen attempted to audition after being told he sounded like a robot. [11] John DiMaggio was eventually chosen for the role after his second audition.The Monument single sized pipe bender measurements can be seen in the image. 15mm standard version is approximately 460mm and the standard 22mm version is approximately 670mm. Combi Bender 2600K MON2600 Rubber feet are available code 2607F which fit the 1215K, 1315XVE, 1315Longarm, 1222G, 1322Extended. Two rubber feet are included in the 22mm versions. The rubber feet also fit the Monument 15mm/22mm combi bender 2600K.

Another way to determine the k factor is by following the “rule of thumb”. Just select a k factor according to your material from the table below. This gives results accurate enough for most cases. A. Cheap thin wall copper doesn’t help the issue, there was a batch a few years ago that was actually snapping. Damaged formers or the guide on bender itself can also do it. Or guides, formers that are not clean (Answered by PG Plumbing on 26 Jan 2021)

The Monument 2600K 15mm and 22mm is a best selling pipe bender. These are available in Monument brand widely available across the UK from plumbers merchants and e-tailers MON2600 2600K, Instinct® brand INST2600 from PHG independent plumbers merchants and also from UKPS plumbers merchants including Plumbase under Entity® brand ENT2600. When initially launched on the UK market Monument ensured that the hook stop was redesigned so as to not mark the pipe.