FireAngel CO-9X-10T-FF Carbon Monoxide Alarm, Multi

Product Information

Do not install CO alarms within 3 metres of doors or windows, above radiators, or immediately close to anything that gives off steam or fumes like a cooker or shower room. Similarly, it is not recommended to install detectors in dusty areas such as workshops or garages. CO detectors should be installed near potential sources of carbon monoxide, essentially any fuel-burning appliances such as boilers, cookers and ovens, fireplaces (both open and enclosed burners), and portable generators. As you are likely to be most affected by CO in areas of your home that you spend the most time in it is advisable to install alarms in those areas as well, such as the living room and bedrooms. It is also worth noting that while one detector is better than no detectors at all, larger homes may require several detectors to cover the property fully.

Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries FireAngel’s new range of carbon monoxide alarms use intelligent sensing technology for a rapid reaction to rising levels of CO.However, if your CO alarm is beeping, flashing red or not responding during a test, follow our troubleshooting guide to decipher the cause. This guide applies to FireAngel FA3313 and FA3820 alarms. Why is my FireAngel CO alarm going off? FireAngel recommend a CO alarm is installed between 1 m and 3 m away from each fuel‑burning appliance, as well as installing additional units in areas such as living rooms and bedrooms where you spend most time whilst at home. Activating your new FireAngel CO alarm In living spaces: they should be positioned close to where the occupant's head is likely to be most of the time – e.g., on your bedside table.

The 7 year sealed battery powered FireAngel CO-9X carbon monoxide alarm features clear LED indicators for power, fault or alarm status and a large test/reset button for ease of testing the device. The CO detector can be wall mounted for home use, or can be left free standing, making it a suitable portable detector to take on holiday.

What's Included?

Known as the ‘ Silent Killer’, CO occurs when fuels burn incompletely, with common sources being boilers, gas fires and hobs and solid fuel burners. However, carbon monoxide can also pass through walls, so you would also be at risk if a neighbouring property had a leak. Find out more about the FA3313X4 CO Alarm. FA6813-EU: Carbon Monoxide Alarm with replaceable batteries To activate your CO alarm, pull the disabling tab out of the alarm and wait up to 1 minute for the green LED to flash to confirm the alarm is active. After 1 minute, press the test button to hear the alarm sound. Please note, the alarm will not sound before the 1 minute activation period is complete. CO alarms and rental properties The advice below is purely provided for ‘best practice’ and should not be used independently. Please note, these alarms are not suitable for homes in Scotland under the new Fire & CO regulations.

With low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate.Our FA3322X4 Carbon Monoxide Alarm with digital display comes with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. If your FireAngel carbon monoxide alarm is new and the test button is not working, try removing the isolation pin. Once removed, wait for at least 1 minute for alarm to initiate. If the alarm now sounds once test button is pressed your alarm is working correctly. If it still does not sound, please get in touch with our Customer Support team. The alarm comes with 2 X AA batteries that can be replaced once the low battery chirp can be heard. Combined smoke & CO alarms or mains-powered CO alarms are typically installed on the ceiling and should be at least 30cm away from any wall, light fitting, or other obstruction.

Looking for a CO-9D alarm replacement? FireAngel’s new FA3322X4 alarm will be replacing any end-of-life CO-9D alarms. If you have had your FireAngel carbon monoxide alarm for a few years but it is still within warranty, and the isolation pin has been removed, please get in touch with our Customer Support team. If it is not within warranty, please replace your alarm as soon as possible. Why is my FireAngel CO alarm beeping? With a multi-functional LCD digital display and array of exclusive features such as Alarm Memory, Ventilate Instruction, Quiet Self Test and Environmental Sensing, the FA3322X4 offers the highest level of CO detection for your home.

Key Product Features

The alarm’s high sensitivity mode will be enabled if the alarm predicts CO levels will increase to or above 180ppm for fast reaction to rising CO levels.