Hmm, I haven’t seen the issue only in Fusion. Does it happen every time you attempt to connect the device, or only on the 2nd etc. times? Can you verify for me what your USB connections are by going to Devices -> USB in the VirtualBox menu? First, sorry for your comment not showing up initially. I manually approve/reject posts to prevent spam even further, which is why this is just now showing up.

Card mạng Wifi Alfa AWUS036NHA AR9271 802.11n Card mạng Wifi Alfa AWUS036NHA AR9271 802.11n

Once I put the device properly in monitor mode, then I ran airodump! root@kali: ~# airodump-ng wlan0monWith everything properly connected and configured, it was time to set up monitor mode. To do this, I started airmon-ng on the wlan0 device. root@kali: ~# airmon-ng start wlan0 wifichanges/wireless-regdb-2013.02.13#make what we want to do here is after the folder is cd just type make If you always travels outstation or overseas and stay in Hotel with Wifi Hotspot, This is your best choice because from my own experience, your Laptop build in Wifi is too weak and always fail to get the connection

AWUS036NHA – ALFA Network Inc.

So I will run into the problem only if I connect, don’t wait, and then attempt to reconnect my device to my VBox VM. I was asking if you go the same issues even after a reboot and attempt to connect it to your VM. I tried everything on this post without success, the blinking green icon on the USB controller wasn't happening for me. ALFA AWUS036NHA is an 802.11n wireless USB adapter from ALFA Network, Inc. with a top connection speed of 150 mbps. It has an Atheros AR9271 chipset Once I created a new blank filter, I just added the appropriate Vendor ID and Product ID and saved it.

usb 2-2: ath9k_htc: USB layer deinitialized

Now however the problem is that when I plug in the Alfa device my network connection from my other wifi ceases to work (Intel(R) Wireless-N 7260) (the connection bridged from my host). It disconnects in the host aswell. If I connect to a wifi (with 7260) in the host with kali and alfa running the alfa stops working in Kali... I want to have them both running. okay basically in at this stage you should see ~/wifichanges/wireless-regdb-2013.02.13#l highlighted in blue after you have Do this for each .pem) usually just 2 files just highlight them and copy from 1 folder to the other if you got lost remember that both the crda-1.1.3 folder and the wireless-regdb-2013.02.13 will both be inside the wifichanges folder located in you home root it dosn't get any easier than that I’ve been running into the same issue with deauth, more specifically, I’m trying this against 5GHz networks. I’m assuming that this is due to client devices getting “smarter” and implementing protected management frames.

ALFA AWUS036NHA Atheros AR9271 802.11n WIRELESS-N - Rokland ALFA AWUS036NHA Atheros AR9271 802.11n WIRELESS-N - Rokland

Alfa AWUS036NHA device problem - error 43 - device descriptor request failed (code 43) if switches between systems and VM. The signal strengths I see with the HA are typically not as strong as what I see with the H. However, this can be misleading since the driver that the manufacturer writes controls this value, and from working on the 8187l driver, I know that it tends to be a bit optimistic. So this in itself is not really too important. They both saw about the same networks. There was some variation at times, with the H tending to see a few more. Again, this fact alone is not that important however, but consumers tend to like devices that show lots of networks, even if they can’t connect to them J. Quantity, government, and military discounts are available. GSA (General Services Administration) compatible. Sometimes retailers have a tendency to promote a specific attribute of a product as if it is the only thing that matters. In fact, while higher output is a good thing, it is not the only thing that determines your range and signal strength.They were both able to connect to the same set of networks where I am currently located, however I need to test this in more locations which will happen as we start to move the boat in 2 weeks. My current location is pretty limited so I don’t think there is anything conclusive from this yet. Just a question on tx power. I setup your script and this is the output. Wondering if I'm getting 20 or 30dBm? Using Kali v2 https://www.cisco.com/assets/sol/sb/WAP371_Emulators/WAP371_Emulator_v1-0-1-3/help/Apx_ReasonCodes2.html

Alfa awus036nha kali linux | Tech Tutorials Using Alfa awus036nha kali linux | Tech Tutorials

After I had the device filter setup, I detached the device from my workstation and logged into Kali. As you can see, there are no wireless devices connected to my VM yet. Welcome to the largest community for Microsoft Windows 10, the world's most popular computer operating system!AWUS036NHA (TP-LINK Wireless USB Adapter) switches between systems without any problems. at boot VB Kali - disconnected from Win10 and connect to Kali, after Kali shutdown, device connected to Win and show in device manager again.